Control

Trident Reagent Kit 6 Month Supply - With six month kits, the cost of running the Trident is less than $17 per month - that’s averages out to about 7 cents a test! Neptune Systems recommends keeping on hand no more Trident reagent than you might...

PLEASE ONLY PURCHASE 1x Two Month Supply.  We will not be able to restock any reagents for the next 30 days. 2-month reagent kit (based on the default testing schedule of 4-Alk/2-Ca/2-Mg per day).  The reagent kit has at least 240...

The Crossover Diet from Neptune Systems is a new type of food that was designed specifically for coral reef tanks and specifically for automatic feeding systems. Working closely with Reed Mariculture (the manufacturer of Reef Nutrition foods) we came up...

Neptune Systems Magnetic Probe Rack Features – MPR: Organizes up to four probes. Designed specifically for the Apex Controller probes, a perfect fit for the thicker temp probes. Built with an all acrylic weather and shatter resistant design...

Replace your Temperature Probe, add one for another tank, or put one on your PM2/PM3 module for temperature compensated readings. Buy this probe if you are: Replacing an old probe. Adding another tank to your system via a PM1. Want to have more...

Feed your fish consistently, and safely, while you are home OR away! NOT A STAND-ALONE FEEDER (MUST BE USED WITH AN APEX SYSTEM) A key component of caring for aquatic animals is regularly providing them with food, but in amounts that get consumed...

The PMUP is a multi-purpose pump that can be used for many different tasks on your aquarium. Automatic Top-Off (ATO) Carbon reactors GFO reactors Biopellet reactors Many other salt or freshwater uses NEW IN VERSION 2: Automatic shut off when...

4-pin male to male cable many of you have been waiting for. It is ten feet long. This cable allows you to connect your DŌS to the 1LINK thereby eliminating the need for the DŌS to be connected to a power supply brick or the AquaBus cable. Just one wire!...

DŌS Replacement Pump Head Cap for your Neptune Systems DŌS module.  Complete assembly includes cover, peri-tube, fittings and roller wheel. Neptune Systems recommends that these be replaced approximately every 700 hours of pump run time.

The ATK (Automatic Top-off Kit) is a simple, standalone, and complete solution for replacing water lost to evaporation. The new aquarium hobbyist has many challenges, but none is more annoying than the chore of adding water, every day, to make up for...

This sensor plugs into your FMM and, using reflected infrared light, will signal your Apex when it changes state from being wet to dry or dry to wet. This sensor can be used for constructing your own ATO (auto-top-off), as a high-level warning sensor in...

Pre-wired Electronic Heating Thermostat Temperature Controller and Digital Timer Controller for Aquariums, now with WIFI control. ITC-306T WIFI is a pre-wired heating output temperature controller with time function specifically for aquariums. It can be...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

This 24VDC powered, normally-closed (NC), solenoid valve has push-fit tubing input and outputs designed for standard 1/4″ tubing. The electrical connection on this solenoid valve fits the DC24 accessory ports found on the FMM, 1Link, and Energy Bar...

The Magnetic Optical Sensor replaces our optical sensor with magnet and offers an improved look, feel, and magnetic design that also lends itself to help prevent water incursion into the sensor. This sensor plugs into your FMM and, using reflected...

Start measuring salinity in your tank and get alerts when out of range. Buy this probe if you are: Replacing an old probe. Adding salinity monitoring to your system via a PM2.

FMM – FLUID MONITORING MODULE IT DOES SO MUCH! This is just the module itself without and sensors. The FMM (Fluid Monitoring Module) is a module that connects to any Apex (Apex(2016), Apex Classic, Apex Lite, Apex Jr.) via it’s AquaBus...

The PM1 probe module is just what you need if you want to monitor pH or ORP in your tank. And, there is an added bonus, you get an extra temperature port as well as six I/O switch inputs for use on ATO, feed buttons, or whatever else you may come up...

Double junction probes place a second vessel inside the main electrolyte with a second internal junction. The means that even when the aquarium water eventually begins to make its way in the first compartment, it still has to go through the second...

Usually used with a return pump, this flow sensor can be placed in line with the flow on any pipe, connected to the FMM, and communicate to your Apex the flow rate of water through that pipe. The flow sensor itself uses BSPP threads so for North...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

Plug this probe into your FMM and then place it on any surface where you want to detect stray water. Upon contact with water this probe will communicate to your Apex and alerts or other actions can then take place.  Time is so critical when it...

New to the leak detector offerings is the Optical Multi Surface Leak Sensor (LD-3).  This is a weighted sensor that is an improved sensor and design over our Solid-Surface Leak Sensor (LD-2).  Those improvements include: An epoxied design...

This Heating Element Required a Heating Controller to Operate! - https://www.saltwateraquarium.com/hc-810m-digital-temperature-controller-up-to-800-watts-finnex/ The Titanium Finnex Heaters are corrosion-resistant, extending the life exponentially from...

Requires a Hydros to Control the Unit The HYDROS Dosing Pump is a simple and affordable way to automate the addition of liquid supplements, trace elements, and two-part solutions to an aquarium. Connect the Dosing Pump to any available HYDROS Control...

* Requires a HYDROS Controller to Operate.  Will not operate standalone. The HYDROS Power 4 WiFi Power Strip is a smart power bar designed to work with the CoralVue HYDROS platform.  The Power 4 has 4 x 120V AC outlets and 4 x USB ports...

Connect external switches and I/O Inputs to your Apex When connected to the I/O Port of your Apex, Apex Lite, or PMx module, the Breakout Box gives you an easy way to connect up to six external switch inputs to your Apex. Examples of things you might...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

With the Fauna Marin Multi-Reference Solution, you can test your test kits under accurate conditions. Our Reference Solution is the first to be based on a saltwater matrix and is quality tested using our ICP-AES testing machine. We use a saltwater matrix...

A redesigned display module has been created with a slick new look that matches the color scheme. Orange LED

Are your corals not as vibrant as you expect? Have you ever had an aquarium crash unexpectedly? Now with the seneye Reef you can continuously monitor and analyze key life-critical parameters in your saltwater aquarium to ensure that your corals and fish...

M series heaters combine modern aesthetics with reliable Italian construction. Employing an ultra-slim profile, M heaters are a welcomed departure from traditional, more bulky designs. The M series is highlighted by its reflective...

Probably the most popular sized level sensor this is the ideal sensor for your average containers used in and around aquarium.  This will be the ideal sensor for measuring the return pump section of your sump.   You will be able to make...

With the EHEIM precision heater your fish receive exactly the right temperature – in any aquarium. Obvious ideas often are the best ones. For example, the aquarium heater as a rod. The heating rod is simply hung in the water and heats it. It is...

The 1LINK module and the EB832 have two DC24 accessory outputs built that act like additional on/off outlets for DC24 devices. There are some Neptune Systems accessories, like our PMUP, that connect to these outputs directly.  There are...

Some of the most successful reef aquariums employ the use of a macroalgae-filled growth area or refugium for the purpose of nutrient control. The GRO is a specialized, 20W LED light designed to grow many types of common macroalgaes (i.e. Chaetomorpha)...